We have uncovered the article pertaining to How to Install a Bathtub down the page on the internet and reckoned it made good sense to talk about it with you in this article.
Mounting a bath tub isn't precisely rocket science, however it does need strong plumbing, carpentry, and also occasionally, tiling abilities. Changing an old bathtub with a new one is likewise a moderately difficult project. If the old tub is conveniently accessible, the project can relocate quickly; if you have to open up a wall surface to remove the old tub and place the new bath tub, the task is a lot harder. In either instance, the job is within a home handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also set in the new one. Make sure you have actually certified on your own for the job as well as are comfortable attempting it. As opposed to hiring a specialist to take control of a halfway-completed job, it is far better to take into consideration using one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new bathtub in your bathroom if you have actually currently bought a brand-new bathtub as well as don't require to change the plan of your previous supply of water pipelines.
Your tools as well as product list ought to make up the following:
Getting ready for the Setup
First of all, the sustaining framework provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps system to avoid strain on the bathtub.
Fit the versatile tap adapters to the bottom of both faucets utilizing 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be suited its last position.
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing faucets can be fairly troublesome because of the limited accessibility that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a cloth prepared for the remaining water that will certainly come from the pipelines. As soon as the supply pipes have actually been eliminated, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any kind of old securing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Mounting the Bathtub
Using both wood boards under its feet, place the bathtub in the called for position. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the bath tub up until the level reads level.
To mount faucets, fit the bottom of the outermost adaptable faucet adapter to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water supply and also inspect all joints and also new pipework for leakages and tighten them if necessary. Load the tub and also inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, deal with the bath paneling as explained in the producer's user's manual. Tiling as well as securing around the bathtub should wait up until the tub has actually been used a minimum of once as this will settle it into its final setting.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making certain that the washers remain in location in between the tap and the sink. Safeguard the tap in place with the maker offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The former type ought to be attached to the faucet finishes first, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the location where the bathroom fulfills the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to break a stiff seal, creating the water to penetrate the wall surface between the bath and also the tiling, bring about difficulties with wetness and also possible leaks to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures and installations. They are marketed in tubes as well as cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always load the tub with water before securing, to allow for the motion experienced when the tub is in usage. The sealer can split relatively very early if you do not think about this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly available on the market. It is suggested to fit the tiles making use of waterproof or waterproof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that piece about A Step-by-Step Guide to Installing a Bathtub while browsing the web. Appreciated our review? Please share it. Let others locate it. Thank you for your time spent reading it.
Need Help? Hire Us Now!